XStream"燨EM燫F燤odule?燩roduct燤anual爒5.x00燵2006.02.24]?/DIV>
SL (Serial Number Low) Command
AT Command: ATSH
Binary Command: 0x26 (38 decimal)
Parameter Range: 0 0xFFFF [read-only]
Number of bytes returned: 2
Related Commands: SH (Serial Number High)
Minimum Firmware Version Required: 4.27C
<Diagnostics> Set/Read the serial number low
word of the module.
SM (Sleep Mode) Command
AT Command: ATSM
Binary Command: 0x01
Parameter Range: 0 8
Parameter
Configuration
0
Disabled
1
Pin Sleep
2
Serial Port Sleep
3
Cyclic 0.5 second sleep
(Module wakes
every 0.5 seconds)
4
Cyclic 1.0 second sleep
5
Cyclic 2.0 second sleep
6
Cyclic 4.0 second sleep
7
Cyclic 8.0 second sleep
8
Cyclic 16.0 second sleep
Default Parameter Value: 0
Number of bytes returned: 1
<Sleep Mode (Low Power)> Set/Read Sleep Mode
Settings. By default, Sleep Mode is disabled and
the module remains continually active.
SM Command allows the module to run in a
lower-power state and to be configured in one of
eight settings.
Cyclic Sleep settings wake the module after the
amount of time designated by SM Command. If
the module detects a wake-up initializer during
the time it is awake, it will synchronize with the
transmitter and start receiving data after the
wake-up initializer runs its duration. Otherwise, it
returns to Sleep Mode and continues to cycle in
and out of inactivity until the Wake-up Initializer
is detected. If a Cyclic Sleep setting is chosen,
the ST, LH and HT parameters must also be set
as described in the Sleep Mode section of this
manual.
Related Commands:
Pin Sleep PC (Power-up Mode), PW (Pin
Wake-up)
牋牘?006燤axStream,營nc.燙onfidential燼nd燩roprietary?/DIV>
32?/DIV>
Refer to the Sleep Mode sections [p13] for more
information.
Serial Port Sleep ST (Time before Sleep)
Cyclic Sleep ST (Time before Sleep), LH
(Wake-up Initializer Timer), HT (Time Before
Wake-up Initializer), PW (Pin Wake-up)
ST (Time before Sleep) Command
AT Command: ATST
Binary Command: 0x02
<Sleep Mode (Low Power)> Set/Read the period
of time in which the module remains inactive
before entering into Sleep Mode. For example: If
the ST parameter is set to 0x64 (100 decimal),
the module will enter into Sleep mode after 10
seconds of inactivity (no transmitting or
receiving). This command can only be used if
Cyclic Sleep or Serial Port Sleep Mode settings
have been selected using the SM command.
Parameter Range: 0x10 0xFFFF
[x 100 milliseconds]
Default Parameter Value: 0x64 (100 decimal)
Number of bytes returned: 2
Related Commands: SM (Sleep Mode), LH
(Wake-up Initializer Timer), HT (Time before
Wake-up Initializer)
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
XIB-R
BOARD INTERFACE RS232/485
ZMN2400HPDB
BOARD ROUTER DEV ZIGBEE 100MW
ZMN24HPDK-B
KIT DEV W/ZIGBEE ZMN2400HP
ZNI1000TC
IC TEMP SENSOR NI1000 SOT23-3
02110102-000
SNSR TILT RATIO 60DEG 500MA FLNG
1-5209285-2
FOPC BOA 12DB FC/UPC BP SM
2-1693560-0
BOA 20DB LC/UPC BB
517SS16
MAGNETIC SENSORS BIPOLAR ICS
相关代理商/技术参数
XIB-R
功能描述:界面模块 RS-232/485 interface 24XStream 9XCite
RoHS:否 制造商:4D Systems 产品:Serial Converters 通道/端口数量: 数据速率: 接口类型:USB, UART 工作电源电压:3.3 V, 5 V 最大工作温度:
XIB-U
功能描述:界面模块 USB interface board 24XStream 9XCite
RoHS:否 制造商:4D Systems 产品:Serial Converters 通道/端口数量: 数据速率: 接口类型:USB, UART 工作电源电压:3.3 V, 5 V 最大工作温度:
XIC25040
制造商:XIC 功能描述:25040 24HR '6
XILINXPWR-079
功能描述:电源管理IC开发工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
XILINXPWR-080
功能描述:电源管理IC开发工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
XILINXPWR-081
功能描述:电源管理IC开发工具 Pwr Mgmt Eval Mod Xilinx RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
XILINXPWR-082
功能描述:电源管理IC开发工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
XILINXPWR-083
功能描述:电源管理IC开发工具 Pwr Mgmt Eval Mod Xilinx RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
